See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
1 Gallon of Plastisol
- Choose Formula
Aluminum Fishing Lure Molds
At a full 18″ the Mega Ribbon is the one of the biggest (if not THE biggest) Ribbon Tail injection worm mold on the market! Featuring a 1/2″ diameter ribbed body, smooth section, and .08″ thick tail. The ribbed body / smooth area is 7.5″ long and the tail is 10.5″ long making for a grand total of […]
Injectors
5.25" Stick bait very similiar to the big brand stick bait of this size. 18 Cavities Made in USA
Safety Products
- Stainless Steel
- Set of four
- Smidgen
- Dash
- Pinch
- Tad
Liquid Plastisol
- 112 Super Soft
- 142 Super Soft/Low Odor/Ultra Clear
- 152 Soft
- 212 Medium
- 232 Medium Non-Phthalate
- 242 Medium/Low Odor/Ultra Clear
- 262 Medium / Saltwater
- 292 medium/hard/low odor/ulra clear
- 312 Saltwater
- 342 Hard/Low Odor/Ultra Clear
- 362 Saltwater Super Tough
Aluminum Fishing Lure Molds
The 9 Inch Pintail Worm is 9 inches total length with a diameter of .35″ at the thickest part of the body that tapers down to .125″ in diameter at the tip of the tail. The taper of the bait starts behind the egg sack area to leave the front of the bait thick where the hook […]
Plastisol Additives
High grade hardener used to get the exact hardness you prefer. Simply add this hardener to any of the plastisols offered and dial in the hardness of your custom bait and tackle. Offered in pints and quarts.
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
Air Clamp/Vise
Recommended air pressure 110 to 140PSI. If possible, use an air inline filter to extend the cylinder life. Always check your compressor for moisture. 6" Base Keep molds centered to get the best out of this clamp. Do not leave plugged in with pressure when not in use. Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. Clean with compressed air. Do not use chemicals or abrasives. (wd40 safe for cleaning) Do not exceed 140 psi. Servicing. Add very little Tool oil once every month. (About 4 drops is all you need to lube the system.) (Do not use WD40 in the air lines.)
Pearls
Color Shifting Chameleon Powder
- Golden / Blue Shimmer
- Blue / Black Sapphire
- Purple / Green Chameleon
- Red / Gold Fire
- Purple / Violet Disco
- Galaxy
- Ghost
- Blue/Silver Blue Bliss
- Super SILVER Sparkle {No color shift}
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4