See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
Bait Plastics Accessories
The Chill-N-Reel Lets you go fishing without putting your drink down! It's a hand-line fishing reel on the side of an insulated drink holder. The Chill-N-Reel is easy to just about any age. Simply pitch the line(with bait on the hook)in the water with the logo-side facing away from you and your favorite beverage in the drink insulator, wait, tug when you get a bite, and hand-reel with your fish on! It's that easy! The patented The Chill-N-Reel drink holder comes equipped with 50ft of 8lb test line, a hook, sinker, and of course a Chill-N-Reel drink insulator to keep your beverage of choice nice and cool so you can "Reel 'em in Cold!"
All
UV Powders - Add UV Powder to your plastisol to create UV reactive baits!
- Blue
- Green
- Orange
- White
- Yellow
Melting Pots
Mixing Melting Pot Mixer attached, mixes while heating, Master heat control regulates the desired cooking temperature automatically. Kit Includes: 6 Quart, 8 Quart, or 10 Quart Pot Mixer Lid ASSM Power Cord Mixer Custom stand offs with high temp washers.
Pearls
UV Powders - Add UV Powder to your plastisol to create UV reactive baits!
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
Epic Bait Molds 5 Inch CLASSIC STICKBAIT MOLDS – 4 and 8 Cavity
The Classic Stickbait features a worm-like rib texture and a gently tapered tail. Designed for the wacky rig, texas rig, carolina rig and other bass fishing techniques. 5″ Classic Stickbait – 4 Cavity Mold size – 3″x6.125″ 8 Cavity Mold size – 6″x6.125″ Bait size – 5″ long x 0.393″ thick More sizes coming soon, email us at EpicBaitMolds@gmail.com if you […]
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4