See our new 142/242 Low Odor/Ultra Clear series!
Bait Plastics, LLC
Injectors
Hand Injectors with Locking Pins. 2" diameter injectors 8oz Injector = $155.99 12oz Injector=$169.99 16oz Injector = $175.99 20oz Injector = $185.99 Dual Kit only = $115.99 Dual 8oz Injector = $369.99.99 Dual 12oz injector = $389.99 includes 2 injectors and kit Dual 16oz injector=$409.99 includes 2 injectors and kit Dual 20oz injector=$429.99 includes 2 injectors and kit All injectors Comes with 2 O-Rings
Air Clamp/Vise
-Fully Machined clamp plates to ensure optimized clamping face. -6" wide base with 8" clamping plates to allow for mold stability and greater clamping surface. -Adjustable height for different mold sizes. -Anti Marring plates to help reduce cosmetic wear of mold surfaces. -Adjustable speed controller to optimize cylinder speed to operator preference. -110-140 psi recommended for operation. -Inline filter recommended to extend the life of the cylinders. -Keep molds centered to get optimal clamping pressure. -Remove air pressure from clamp after each use. -Usage of the clamp can pinch hand, finger or ect. Using this clamp the operator/owner of the clamp takes full responsibility of usage of the device. -Clean with compressed air and WD-40 only. -Do not exceed 140 psi. -Lubricate system with 1 drop of pneumatic tool oil per week of use. ***Frequent use may require more frequent lubrication. ***LUBRICATE WITH PNEUMATIC TOOL OIL ONLY***
Aluminum Fishing Lure Molds
4.2" Original Beaver
Aluminum Fishing Lure Molds
3.5" craw comes standard with legs. Single Cavity by Kearby Design & Manufacturing LLC Made in USA
Aluminum Fishing Lure Molds
4.65" Hog mold Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similar baits. Single Cavity
Aluminum Fishing Lure Molds
4" Long bug, excellent action in the water. The body of this bait and nose is thicker to give the bait more durability than similiar baits. 16 Cavity Made in USA
Quality supplier for all Soft Bait Making products.
Bait Plastics offers soft bait supplies for the DIY lure maker. We ship Plastisol, Pigments, Glitters, Scents, and a full range of Plastisol additives.
Aluminum Fishing Lure Molds
10 Inch Flat Tail Worm 4 Cavity
Aluminum Fishing Lure Molds
This “fluke style” or “jerk bait” style bait measures 5 inches from nose to tail with a body width of .38″ and a mid body thickness of .6″. The belly features a deep hook slot to allow great hookup ratios on ewg style hooks. The back features a divot down the center for aligning and […]
Accessories
The Next Level 6210 is a premium CVC crew neck. This relaxed-fit short-sleeve t-shirt is fabric laundered 60/40 combed ringspun cotton/polyester made of 32 singles with a set-in 1x1 baby rib collar and tear away label. Material: Cotton, Cotton Blend, Fleece, Jersey, Polyester, Rayon
Aluminum Fishing Lure Molds
The 2 Inch Curly Tail Grub bait is just under 2 inches from nose to tip of tail with the tail extended. It features a ribbed body that has a thickness of .25″ and length of .85″. The tail is thin and very “curled” to create a very flowing back/forth twisting motion while on the […]
Aluminum Fishing Lure Molds
The ned craw bait measures 2.5″ from tail to tip of claws. Featuring 3D claws, short ned rig style body, 6 legs, and small antenna. 4 cavity
Aluminum Fishing Lure Molds
Epic Bait Molds 3″ SLICK SWIM PADDLE TAIL SWIMBAIT (NO HOOK SLOT) – 6 CAVITY TOP SHOOT
The 3″ slick swimmer paddle tail swimbait’s body is just under .5″ thick and .375″ wide. The bait has a big side to side tail wobble with body roll at slow speeds and ultra fast, hard kicking action at higher speeds. This is a 6 cavity “top shot” mold which allows you to use two injectors […]
.025 HEX Fluorescent GLITTER
- Pink
- Lime
- Yellow
- Orange
- Blue
Aluminum Fishing Lure Molds
The 3 Inch Epic PreyBait, “hand injection” style mold was designed as part of a collaboration with Marling Baits. The Epic PreyBait is a boot tail swimbait with a rear fin designed to have an intense action with realistic presentation at any speed, with a kick and wobble on the fall. This bait/mold does not have a hook slot and is intended to […]
Plastisol Additives
High grade hardener used to get the exact hardness you prefer. Simply add this hardener to any of the plastisols offered and dial in the hardness of your custom bait and tackle. Offered in pints and quarts.
We love the opportunity to speak with our customers and can be reached
at 800-427-5819 or csr@baitplastics.com
Wanting to learn more about Bait Plastics formulas and making your own soft baits. Click here for helpful tips!
Feature Products
Scent
The best scents on the market. Add these scents to the finished baits or bag to attract your trophy fish!
- Anise
- Cappuccino
- Crawfish Oil
- Garlic
- Herring
Plastisol Additives
4 Ounce Dipping Dye with UV. Instantly change your baits color
- UV Clear
- Green
- Chartreuse
- Orange
- Red
All
Hanging Bait Bags - Laminated 3 x 3 4 x 4 5 x 3 6 x 4 7 x 4.25 8 x 5 9 x 4 12 x 4